contact@vividsplashbacks.co.uk UK made bespoke glass splashbacks Contact Us

How to measure for a glass splashback

First, check what surrounds the glass. A cabinet, side wall, worktop or extractor can give you a fixed edge. An open edge has clear space beyond it, so you choose where the glass stops.

Width: If the glass has to fit between two things, such as two cabinets, take 5 mm in total off the narrowest gap. If either side is open, keep your chosen width.

Height: Between a worktop and an extractor, take 3 mm in total off the shortest gap. If the space above is open, keep your chosen height. If you have an upstand, start at the top of it.

If there’s a socket or switch in the splashback area, contact Vivid before ordering.

Read the illustrated steps
Illustrated kitchen with a lemon glass splashback fitted above the hob.

Measuring your kitchen, step by step

Measure once your worktop and any cabinets or extractor are in their final positions. On the metric side of a standard tape, the numbers are centimetres and each small division is 1 mm. Write down width first, then height, both in millimetres. For example, 110 cm is 1100 mm.

  1. An open wall above a hob with a dashed splashback outline. The horizontal arrow shows 1100 mm wide and the vertical arrow shows 900 mm high.

    Check which edges are fixed and which are open

    Look to the left, right and above the glass. In this picture there’s a worktop below, but nothing at the sides or above. You can choose both the width and the height. In your kitchen, look for anything the glass has to fit between, such as two cabinets, or a worktop and an extractor.

  2. A level tape reads 110 cm between two cabinets. The pink width label shows 1100 mm.

    Measure the width

    Hold a metal tape level from left to right. Between cabinets or side walls, measure the gap at several heights and write down the narrowest width in millimetres. If either side is open, measure to the spot where you want the glass to finish.

  3. A vertical tape reads 90 cm from the worktop to the underside of the extractor. The pink height label shows 900 mm.

    Measure the height

    If there’s an upstand, measure from the top of the upstand. Otherwise, start at the finished worktop. Measure straight up to the underside of the extractor at the left, middle and right, and record the shortest height in millimetres. With an open top, measure up to your chosen top edge.

  4. A lemon-patterned glass splashback fitted between the cabinets and below the extractor.

    Work out the size to order

    In this kitchen, the narrowest gap between the cabinets is 1100 mm. Take off 5 mm once and order 1095 mm wide. The shortest gap from the worktop to the extractor is 900 mm. Take off 3 mm once and order 897 mm high. If either side is open, keep your chosen width. If the top is open, keep your chosen height.

What size splashback should I order?

Order online from 110 mm to 1200 mm on each side, in whole millimetres. Need something smaller or larger? Contact us and we’ll quote.

Worked example: 1100 mm wide by 900 mm high

Here’s how the size to order changes when you add cabinets at the sides, an extractor above, or both. Use your own measurements when you order.

Example finished glass sizes for a measured area of 1100 mm by 900 mm
Kitchen layoutOrder widthOrder height
Open sides and open top1100 mm900 mm
Between cabinets, worktop to extractor1095 mm897 mm
Open sides, worktop to extractor1100 mm897 mm
Between cabinets, open top1095 mm900 mm

Will the glass fit past the cabinet fronts? Check the gap at the front of the cabinets as well as at the wall. A projecting trim, handle or pelmet can leave enough room for the finished panel at the back but too little room to get it into place. If the entrance is narrower, send us a photo and both widths before ordering.

Enter the size you want the glass to be. We don’t take anything off. If you’ve already taken 5 mm off the width or 3 mm off the height, enter that number. Your artwork proof does not check your measurements. It shows the design. Glass manufacture starts as soon as you order. Toughened glass can’t be cut or drilled afterwards, so please measure twice.

Common cooker and range cooker widths

If you want the glass to line up with your cooker on an open wall, use its width as a starting point. The model name can give a rounded size. Check the specification for your exact model, then measure where the glass will sit.

Advertised size and actual appliance width for selected UK cookers.
Cooker modelAdvertised sizeAppliance width
Beko KDC5422A electric50 cm500 mm
Smeg Victoria 60 electric60 cm600 mm
Rangemaster Classic Deluxe 90 Dual Fuel90 cm900 mm
Rangemaster Classic Deluxe 100 Dual Fuel100 cm994 mm
Belling Farmhouse 100E100 cm996 mm
Rangemaster Classic Deluxe 110 Dual Fuel110 cm1092 mm

Between cabinets? Measure the gap itself. If the narrowest gap is 1000 mm, take off 5 mm and order 995 mm wide. Check the height separately.

Glass splashback measuring FAQs

What if there’s a socket or switch where the glass will go?

Tell us whether each socket is single or double. The standard cut-out is 75 × 75 mm for a single socket and 135 × 75 mm for a double socket.

Facing the wall, take two measurements in millimetres to the centre of each socket box:

  1. Measure across from the left edge of the planned glass to the centre of the box.
  2. Measure up from the bottom edge of the planned glass to that same centre.

Contact Vivid before ordering with a sketch showing these measurements and a photo of the area. If you have a switch or a non-standard socket, tell us so we can confirm the cut-out.

When should I take my final measurements?

Wait until the worktop and any cabinets, upstand or extractor that will border the glass are in their final positions. If the splashback will sit above an upstand, measure the height from the top of the upstand.

What if the gap is wider at the top than at the bottom?

Use the narrowest gap between the cabinets. If your readings are 802 mm, 800 mm and 801 mm, start with 800 mm. Take off 5 mm once and order 795 mm wide. If the opening is visibly out of square, ask Vivid to check the layout before ordering.

Do I take the allowance off at each edge?

No. Between two cabinets or side walls, take 5 mm in total off the width. Between the worktop or upstand and the extractor, take 3 mm in total off the height. The finished glass can vary by up to 2 mm either way (±2 mm), so these gaps leave room even if the panel is slightly larger than ordered.

Width: If the narrowest gap between two cabinets is 800 mm, order 795 mm wide. If either side is open, keep your chosen width.

Height: If the shortest gap from the worktop to the extractor is 900 mm, order 897 mm high. If the space above is open, keep your chosen height.

Why are millimetres best for measuring my splashback?

Each small mark on a metric tape is 1 mm, and our order form uses whole millimetres. If your tape reads 72 cm plus three small marks, write down 723 mm. Rounding it to 720 mm would lose 3 mm before you’ve even worked out the size to order.

Vivid Splashbacks

Bringing you the highest in quality digitally printed splashbacks

Discover the pinnacle of kitchen elegance with our high-quality, digitally printed splashbacks, each meticulously crafted from premium 6mm low iron glass for clarity and strength. Hand-finished with polished and bevelled edges, our splashbacks are not only heat resistant but a bespoke centerpiece for your kitchen, embodying unmatched durability.

Based in the heart of England (Sutton Coldfield, West Midlands), our dedicated design team works with you to bring a unique vision to life, ensuring that each splashback is a perfect blend of function and personalised artistry. Elevate your kitchen with a piece that’s crafted to impress and built to last.

Girl holding one of our highland cow printed splashbacks